By the time the first warm days arrive, a hive has spent months accumulating dead bees, wax cappings, mouse droppings, mould, propolis and moisture damage. Spring cleaning resets the hive for the season. At its simplest, it means swapping the dirty bottom board for a clean one. At its best, it also includes inspecting and replacing old comb, scraping boxes, checking for pests, and recording what the debris tells you about how the colony wintered. This article describes how to do a bottom board change, what the floor debris reveals, and which other cleaning tasks are worth the effort.
Why change the bottom board
Over winter, dead bees fall to the floor, and in a hive with a solid bottom board they can pile up and block the entrance. Debris holds moisture, harbours wax moth larvae, and in warm weather can encourage mould and beetles. A clean board gives bees a fresh start, reduces disease pressure and lets you inspect the floor for signs of problems.
The bottom board swap is usually done on the first warm day suitable for a brief inspection, often combined with your first look at the colony. It takes only a few minutes if you work with a partner and have a clean board ready. If you have a screened bottom board, you simply scrape or rinse the tray and inspect the debris. See Bottom Boards: Solid vs. Screened and Screened Bottom Boards: Varroa Reduction for the options.
Step-by-step: the bottom board swap
- Choose a warm, calm day above about 55°F (13°C), with bees flying.
- Prepare a clean, dry bottom board that matches the hive footprint. If you use a spare, scrape and sanitise it the previous autumn.
- Smoke the entrance lightly and lift the lid and inner cover to let the bees settle.
- Place the clean board on the ground or stand beside the hive.
- Lift the entire stack of boxes and set it on a spare lid, upside down cover or other platform.
- Put the clean board in place and lower the boxes on to it, aligning the corners.
- Check that the entrance is clear and the boxes are level.
If you lack a helper, split the stack and move boxes one at a time, but be careful not to crush bees. Do not work during rain or chilly winds.
Reading the debris
The floor of a hive is a diary. A scattering of dead bees is normal. A large mass of dead bees suggests the colony struggled, with possible causes including starvation, cold snaps or disease. Look at the position of dead bees: head-first in cells may indicate starvation, while piles near the entrance might point to a robbing attack or poor ventilation.
Wax cappings indicate where the cluster has been eating honey. A compact pile suggests a tight cluster, while a scattered pattern suggests the cluster has moved. Mouse droppings and chewed comb show that rodents got in. Moth webs and larvae suggest wax moth; see Wax Moth: Greater and Lesser. Mites in debris can be counted to estimate infestation, though a more reliable method is described in Varroa Monitoring: Alcohol Wash vs. Sugar Roll. Healthy colonies leave tidy debris of wax and a few bees.
Cleaning and sanitising the used board
Scrape the board with a hive tool to remove debris. If it is wooden, flame-scorch it lightly with a torch to kill spores and pests, taking care to avoid fire hazards. Alternatively, wash with a washing soda solution, rinse well and let dry in the sun. Avoid using bleach or harsh chemicals that leave residues. If you suspect American foulbrood in a colony, do not reuse equipment, and contact your apiary inspector; see American Foulbrood (AFB): Identification and Response and Apiary Hygiene: Equipment Cleaning and Disinfection.
Dry the board thoroughly before reuse. Check for rot, cracks, warping and gaps. Replace damaged boards, and repair small cracks with wood filler designed for exterior use. Painting the outside with exterior latex paint helps preserve it; see Painting and Preserving Bee Equipment. Keep a few spare boards so you can swap quickly in every yard.
Other spring cleaning tasks
Scrape propolis and burr comb from box rims and tops of frames. This restores bee space and makes boxes easier to take apart. Remove and replace broken or badly stained frames, placing new drawn comb at the edges of the brood nest. A common guideline is to replace about a fifth to a third of the frames each year so that no comb remains in service for more than several years; see Comb Rotation: Why and When and Old Comb: Contaminant Accumulation.
Check inner covers and outer covers for leaks, warping or rot, and repair or replace as necessary. Clear the entrance of debris. Clean feeders, mouse guards and entrance reducers, and remove mouse guards once temperatures rise and robbing is no longer a problem. Take down insulation or wraps when daytime temperatures consistently stay well above freezing.
Keeping disease risks low
Cleaning is not only about appearance. Pathogens can persist on old equipment. Scrape and, if appropriate, scorch equipment that has been used with sick colonies. Never exchange frames among colonies unless you know their health status. Sterilise tools between hives or yards, especially if you suspect disease, by dipping in a solution recommended by your apiary inspector or by flaming.
Dispose of dead bees and debris away from apiaries, preferably burying or bagging them. Don't leave honey or wax out where bees can rob. If you have a large apiary, keep records of which board or box was used with each colony, so you can trace issues. Our guide to Foulbrood Spore Detection: Testing Options explains testing, and Apiary Hygiene: Equipment Cleaning and Disinfection has more on routine hygiene.
Timing and workflow
In a large apiary, combine the clean-out with the first inspection to minimise disturbance. Bring spare boards in a truck, work quickly down the row, and place used boards in a separate area to scrape later. Keep a notebook to record what you find under each hive. If you notice a pattern, such as multiple colonies with dysentery, you may need to address a broader issue such as moisture or nosema; see Nosema Diagnosis and Treatment.
If the weather turns cold after you open the hive, you can reduce harm by working quickly and closing up. For beginners, spring cleaning is one of the best ways to learn what a healthy winter looks like. Pair this article with Early Spring: First Inspections and Feeding for a full first inspection routine.
FAQ
How often should I change the bottom board?
Once a year in spring is a good habit, with extra checks if you suspect pests or heavy debris. A screened board can be cleaned instead of replaced.
Can I reuse a bottom board from a dead hive?
Yes if the colony died of starvation or cold, after scraping and sanitising. If disease such as foulbrood is suspected, consult your apiary inspector before reusing equipment.
What do dead bees on the floor tell me?
A small number is normal. Large piles may indicate starvation, disease, cold snaps or poor ventilation, so check the position and the stores to work out what happened.