Reversing is a spring technique in which the beekeeper swaps the positions of two brood boxes, putting the lower box on top and the upper box on the bottom, so that the queen has fresh room to lay and the colony feels less crowded. It has a long history in beekeeping manuals and is still widely taught. It also has vocal critics who say it disrupts the brood nest and does little to prevent swarming. This article explains the reasoning, describes how and when to reverse, weighs the advantages and drawbacks, and offers alternatives for beekeepers who prefer not to do it.
Why bees move upward
During winter, the cluster begins low in the hive and moves upward as it consumes honey, so by early spring the bees and the first brood are often in the top box, with the bottom box empty or holding a little leftover honey. As the colony grows, the queen continues to lay near the top. If the top box fills with brood and honey, the bees feel crowded, though there is a large empty box below.
Bees have a strong tendency to expand upward, and they are reluctant to move down into empty space. The theory behind reversing is that by placing the empty box on top, you open the brood nest upward into new space, tricking the queen into laying in the lower box and reducing congestion. The overall pattern of colony growth is discussed in Understanding Colony Growth: Spring Buildup and Spring Buildup: Managing Explosive Growth.
How to reverse
Choose a warm, calm day in early to mid-spring, when brood is present and temperatures are stable, typically when dandelions bloom or the first strong flow starts. You should not reverse in a cold snap or when the colony is small. Make sure the queen is laying in the top box and that the bottom box is clean and mostly empty of brood.
- Remove the lid and inner cover and set them aside.
- Lift off the top box, which holds the brood nest and most of the bees, and rest it on an upturned lid.
- Scrape and tidy the bottom board while the hive is open; see Spring Cleaning: Bottom Board Changes.
- Lift the empty former bottom box and set it on top of the brood box, so the two boxes have swapped places and the empty comb now sits directly above the brood.
- Replace the inner cover and lid, and reduce the entrance if the weather is cool.
The aim is to leave the brood nest sitting in the lower part of the hive with the empty comb directly above it, so the queen can move up into fresh cells. Check in a week or two to see where the brood is, and whether the bees have moved the cluster back up.
Advantages
Proponents argue that reversing relieves congestion, encourages the queen to lay in more cells, and reduces the risk of swarming. It also redistributes honey, putting stored honey above the brood where bees can reach it. It is a quick manoeuvre and requires no extra equipment. For beekeepers with a lot of hives, it can be a speedy way to give space.
Reversal can also help beekeepers who have colonies that built up in the top box and are crowded, but who are not yet ready to add a second brood box or a super. It can be combined with cleaning the bottom board, as described in Spring Cleaning: Bottom Board Changes, to make the best use of the visit. For beginners, reversal gives a clear and repeatable task in spring.
Drawbacks and criticisms
Critics point out that reversing disrupts the brood nest. The bees must rearrange it, and brood may be chilled if the weather turns cold. The cluster tends to move upward again, and the effect may be short-lived. Field experience suggests that reversing does not reliably prevent swarming; in some cases the disruption triggers it.
Moreover, if the colony is small or the weather unreliable, reversal can set it back. Another concern is that it may separate the queen from her brood, or place nectar in the brood nest. In regions with a short spring and rapid buildup, adding supers or splitting may be more effective than moving boxes around. Evidence is mixed, and opinions are strongly held, so treat claims on both sides with scepticism and experiment with a few colonies.
When not to reverse
Avoid reversing if the colony is small, if the weather is cold, if the brood nest spans both boxes in good order, or if you suspect disease. Do not reverse a colony in the middle of a strong flow, when the bees are filling the boxes with nectar, because the swap could scramble the stores. A colony in a single deep or a hive with a brood nest in the lower box does not need it.
Also avoid frequent reversals. One or two in spring is plenty. Excessive manipulation stresses the colony and wastes time. Some beekeepers prefer to leave the brood nest alone and add boxes on top, a practice called "supering up" or adding boxes above as space is needed; see Adding Supers: Timing and Configuration.
Reversal in practice: a worked example
Imagine a ten-frame, two-deep hive in mid-April with dandelions in bloom. The bees and brood occupy the top deep, with five frames of brood, while the bottom deep holds only a little capped honey on the outer frames. If left alone, the queen will fill the top box in two to three weeks and the colony will begin building queen cups. By swapping boxes on a warm afternoon, you place the empty bottom box above the brood, and the cluster treats that comb as new territory.
In practice, the effect lasts about two weeks. After that, the colony usually adds brood in the upper box and the nest again becomes congested, so a second step, such as adding a super or a third brood box, is needed. Treat reversal as a short-term tool, not a complete swarm-control program, and you will avoid disappointment.
Alternatives to reversing
Many beekeepers achieve the same goal by adding a box with drawn comb at the top, removing honey frames from the brood nest, or by checkerboarding stores. Others use splits, as described in Making Splits: Techniques and Timing, to relieve congestion and obtain increase. A third option is to move frames of capped brood upward and replace them with drawn comb in the lower box, an approach that keeps the brood nest intact.
Another approach is the use of a single large brood box such as a ten- or twelve-frame deep with ample space, or a horizontal hive that avoids the stacked-box problem. Different hive types handle this differently; see Horizontal Hives: Long Langstroth and Layens and Langstroth Hive: The Standard Explained. The best approach depends on your climate, your hive type and your management style.
FAQ
What is the purpose of reversing brood boxes?
It aims to give the queen and bees more room by moving the empty bottom box to the top, reducing congestion and perhaps swarming risk.
Does reversing prevent swarming?
Not reliably. Evidence is mixed and some beekeepers find it can trigger disruption. Space, splits and good management are more dependable.
When should I reverse?
Only on a warm, calm day in spring, when the colony is strong and brood is present, and not during cold snaps or a strong flow.