Beekeeping Directory

Home › Guides › Equipment & Hive Types › Bottom Boards: Solid vs. Screened

Equipment & Hive Types

Bottom Boards: Solid vs. Screened

The bottom board is the floor of your hive and the part most beekeepers think about least until it causes trouble. It controls the entrance, ventilation from below, debris removal and, in some designs, the sampling of varroa mites that fall from the cluster. Solid and screened boards each have a real case in their favor, and the right choice depends on climate, hive strength and how you manage mites. This article compares the two, explains reducers and sliding trays, and gives you a practical way to decide for your own apiary.

What a bottom board does

A bottom board supports the weight of the hive and defines the entrance. Bees enter and leave through a slot between the board and the lowest box, usually 3/8 inch deep and the width of the hive. A reducer shrinks that opening in cold weather or when a colony is small and defending against robbers, and a landing platform in front gives returning foragers somewhere to land.

The board also determines how air moves through the hive. Warm air rises, so the bottom of the hive is a natural inlet for fresh air. A solid board holds in warmth and blocks drafts, while a screened board lets air, and some mites and debris, fall through. Neither is wrong; each shifts the balance between insulation and ventilation.

Finally, the board is a wear item. It sits at the bottom of the stack, takes rain splash and gets propped by mice and bees' debris. Plan to replace it every several years even with good paint or wax treatment. For how the bottom board fits into complete assemblies, see Assembling Your First Hive: A Beginner's Guide.

Solid bottom boards

A solid board is simply a flat floor with side and back rails that form the entrance. It is simple to build, cheap to buy and very durable, and it keeps winter wind out of the hive. In cold climates many beekeepers prefer solid boards, particularly with smaller colonies that struggle to keep the brood nest warm.

Solid boards have drawbacks. Moisture and dead bees accumulate on the floor, and in warm weather the lack of lower ventilation can leave colonies bearding at the entrance. Hive beetles and wax moth larvae use the debris layer to breed, so you need to scrape or replace boards regularly. Reversible solid boards have a deeper and a shallower entrance on opposite sides, which you flip with the seasons.

Wood solid boards last longer if the underside is painted and the top is left bare or lightly waxed. Plastic solid boards resist rot completely but can warp in sun and crack in cold; many beekeepers pair them with a wooden stand to cushion them.

Screened (open mesh) bottom boards

A screened bottom board replaces most of the floor with 1/8 inch hardware cloth, small enough that bees cannot pass through but large enough for varroa mites that fall off adult bees to drop out of the hive. Many models include a removable tray underneath so you can slide it in and count mites. The mechanics and limits of this tool are covered in Screened Bottom Boards: Varroa Reduction and the counting method appears in Varroa Monitoring: Alcohol Wash vs. Sugar Roll.

Screened boards improve ventilation dramatically. In hot summers they cut bearding, reduce condensation and help colonies cure nectar. They also give you a quick look at the colony: debris on the tray tells you about brood position, wax cappings and ant activity.

The honest caveat is that screens alone do not control mites. Research and beekeeper experience show only a modest reduction in mite populations, because many mites that fall from bees climb back or are carried in capped brood. Treat the board as a monitoring and ventilation tool, not a treatment.

Comparing the two

FactorSolid boardScreened board
Winter warmthBetter, less draftNeeds tray or cover in cold
Summer ventilationLimitedExcellent
Mite monitoringPoorEasy with tray
Debris and pestsBuilds up on floorFalls through, but tray needs cleaning
CostLowModerate
DurabilityHighMesh can rust or tear

Most beekeepers end up with a mix, often using screened boards year-round in the South and screened boards in summer, swapped for solid or covered ones in winter in the North. Colonies also vary; a strong hive in a sheltered spot can handle open mesh while a weak nuc cannot.

If you keep only one or two hives and want one board for every season, a screened board with an insert tray you can slide in during winter is the most flexible compromise. Test it on one hive before you buy for all.

Managing screens in winter

An open screen in a northern winter can chill the cluster and cause more consumption of stores. The fix is not to avoid screens entirely but to close them. Slide in the tray or a sheet of corrugated plastic to block the mesh, leaving the entrance reducer in place. The colony still gets the benefit of a landing area and drained moisture.

Do not close the screen so tightly that moisture cannot escape. Condensation is a bigger winter killer than cold, and a hive with no upper ventilation or no bottom drain can drip water onto the cluster. Pair a closed lower screen with upper ventilation, either a notch in the inner cover or a small upper entrance. See Winterizing Hives: Insulation and Ventilation for a complete approach.

In mild climates, many beekeepers leave screens open all year and add a mouse guard in autumn. Observe your own colonies; cluster size and weather decide, not rules.

Entrance reducers and landing boards

The reducer is a notched wooden or plastic strip that sits in the entrance and narrows it to roughly 1 1/2 to 3 inches. Use the smallest opening in early spring when bees are few, after splits, during nectar dearths and whenever robbing starts. See Robbing Behavior: Prevention and Response for signs and responses. Remove or widen it during strong nectar flows.

A landing board extends the floor forward by a few inches. Bees prefer it, and tired foragers often land there. In hot weather a long landing board can host bearding clusters, which is normal and not a sign of swarming by itself.

Mouse guards, often a strip of metal with holes bees can pass through, go on in autumn and come off in spring. Keep them snug against the box, because a mouse can squeeze through an opening of about 3/8 inch.

Maintenance and cleaning

Inspect bottom boards at least twice a year. In spring, scrape off dead bees, wax debris and propolis, and check for wax moth larvae, small hive beetle and mould. A hive tool or putty knife works. In autumn, check for cracks, loose screws and rust on mesh.

Swap a dirty board for a clean one instead of working over the hive. Many beekeepers keep a spare board so they can lift the colony onto a fresh board in one move, and scorch or scrub the old one at leisure. Do not use harsh chemicals or strong disinfectants on wood bees will contact.

Paint the outside with exterior latex in a light colour, leave the inside raw, and let it dry before use. Bees rarely chew sealed wood, and a clean dry board resists pests for years. Store boards flat and dry, as described in Storage: Keeping Equipment Clean and Dry.

Choosing for your climate and goals

Use a decision approach. If you live where winters stay below freezing for months, begin with a solid or tray-covered screened board and add upper ventilation. If summers are hot and humid, prefer a screened board with the tray removed. If you monitor varroa often or sell nucs, the screened board with a tray pays for itself in counts.

If you plan to start with a package or nuc, note that small colonies in cool spring weather do better on closed floors. As they grow, you can switch to screen. Match the board to the colony, not the other way around.

Whatever you choose, keep it level, free of vegetation and well supported, as in Hive Stands: Types and Construction. A good bottom board is cheap insurance for the whole hive.

FAQ

Do screened bottom boards control varroa?

Not by themselves. They let some fallen mites drop out and make monitoring easy, but studies and field experience show only a small effect on mite loads, so use them with proper monitoring and treatment.

Should I use a solid bottom board in winter?

In cold climates most beekeepers close the screen with a tray or insert and keep a reduced entrance, which gives a draft-free floor while still allowing moisture to drain. Provide upper ventilation too.

How often should I replace a bottom board?

Wood boards often last five to ten years with paint and good drainage. Replace one that is soft, warped or cracked, and swap in a clean board whenever it is badly soiled.

Keep learning

Browse all 500 guides →