Beekeeping Directory

Home › Guides › Hive Management by Season › Fall Inspections: What to Check

Hive Management by Season

Fall Inspections: What to Check

Fall inspections are different from spring ones. You are not looking for growth but for readiness: Does the colony have a good queen, enough bees, enough food, and a low enough mite load to survive winter? The decisions you make in this one or two visits, including feeding, combining, treating and wrapping, determine the winter survival rate of your apiary. This article gives a checklist of what to inspect, how to do it quickly in cooling weather, and what to do with what you find.

Timing and conditions

Do your main fall inspection in early fall, when temperatures are still warm enough to handle frames without chilling brood. In most temperate regions this means September, though it varies by latitude. Choose a warm afternoon with little wind, and be quick. Open as few hives as necessary for any full inspection and keep boxes covered.

Late fall, after the first hard frosts, is too late for a full examination. By then, bees are forming clusters and the queen is barely laying. Limit yourself to hefting and external checks. The thinking in Fall Feeding: 2:1 Syrup and Fondant and Winter Preparation: The Complete Checklist assumes you have done your inspection earlier, giving time for feeding and treatment to take effect.

Queen and brood

Look for evidence that the queen is present and laying, such as eggs and young larvae. A good fall colony will still have a brood pattern in the centre of the nest, although smaller than in summer. The pattern should be compact with few gaps; see Recognizing a Healthy Brood Pattern. Drone brood in fall is a bad sign, indicating a failing queen or laying workers.

If the colony is queenless in fall, it is often better to combine it with a strong colony than to try to requeen, since new queens may not mate well in cool weather and drones are being expelled. See Combining Weak Colonies: Newspaper Method. A failing queen can sometimes be replaced if you act quickly and you can buy a mated queen; see Queen Introduction: Direct vs. Cage Methods.

Population

A colony going into winter should have a decent number of bees. As a guide, a colony whose bees cover at least eight or nine frames when you check on a cool morning is generally in good shape. Colonies with fewer than about five frames of bees in northern climates often do not survive. Many beekeepers consolidate small colonies in fall.

Check that the population is made up of fresh bees rather than aged foragers. A good fall colony will have many young, pale bees. If you see lots of ragged-winged bees with little brood, the colony may be weakened by mites and virus; see Deformed Wing Virus (DWV): The Varroa Connection. Crawling bees or dead bees at the entrance may signal poisoning or disease.

Food stores

Stores are the number one concern. Weigh or heft each hive, and inspect frames. A two-deep colony in cold climates should have heavy upper boxes with honey capped across the top and sides, and typically 60 pounds or more across the hive. Where winters are milder, less is needed. If stores are short, feed 2:1 syrup now; see Fall Feeding: 2:1 Syrup and Fondant.

Also check that honey is positioned correctly. Bees need food above and next to the cluster, and a colony with honey far from the cluster can starve with food in the hive. Pollen stores are a bonus. Colonies with fresh pollen in the combs will build up earlier in spring.

Disease and pests

Monitor varroa with an alcohol wash. If mites are high, treat according to the label and local rules, then retest. See Varroa Monitoring: Alcohol Wash vs. Sugar Roll and Integrated Pest Management for Varroa. Look at brood for foulbrood signs such as sunken cappings and ropy larvae; if you suspect disease, contact your state apiarist or extension service. See American Foulbrood (AFB): Identification and Response and European Foulbrood (EFB): Stress-Related Disease.

Also check for small hive beetle, wax moth and nosema signs such as dysentery stains, though these are best confirmed with microscopy; see Nosema Diagnosis and Treatment. Colonies that have lost brood to chalkbrood, or have had poor performance, should be considered for requeening next spring.

Equipment and site checks

Inspect boxes for cracks, rot and gaps. Replace damaged bottom boards, and ensure hives are level with a slight tilt forward so water drains. Install mouse guards before the first frost; see Mouse Guards and Entrance Reducers. Check that stands are stable and that your electric fence, if you use one, is working, since bears are particularly active in fall; see Setting Up an Electric Fence for Bear Protection.

Reduce entrances to deter robbers and mice, and ensure ventilation. Remove empty supers and store them. Wrap or insulate according to your climate; the options are in Winterizing Hives: Insulation and Ventilation.

A fall inspection scoring table

ItemGoodNeeds action
QueenEggs and compact broodNo eggs, drone brood
PopulationCovers 8+ framesFewer than ~5 frames
StoresHeavy, capped honey above clusterLight hive, honey far from cluster
MitesBelow threshold or treated and retestedAbove threshold
DiseaseNone seenSpotty brood, odd smell
EquipmentSound, levelCracks, gaps, tilt

What to do with the results

Mark every hive with a simple grade, such as A, B or C. A-colonies go through winter as they are. B-colonies need feeding or treatment. C-colonies are candidates for combining. Write the grades on the lid or in your notebook.

Be honest about weak colonies. A small, queenless or heavily infested hive will rarely recover in time, and combining it with a strong colony gives you a better chance of a good spring. Use the newspaper method and give the combined colony extra feed. Fall inspections are the time for hard decisions, and they pay off the following spring.

Moving frames and rearranging for winter

A fall inspection is also a chance to arrange the boxes for winter. Bees will cluster in the lower box in early winter, moving up as they consume stores, so honey should be above and around the brood nest. If the colony has a brood nest in the lower box and honey above, leave things alone. If the top box is empty and the bottom box heavy with honey, you may want to swap them, though you should only do this while the weather is still warm enough for bees to adapt.

Remove excess empty frames if the colony occupies fewer than the full box. A box half full of bees is hard to keep warm, so use a follower board or dummy frame to shrink the space. Also remove queen excluders, which can trap a cluster away from its honey in winter; see Queen Excluders: Pros, Cons, and Proper Use. Make sure no honey supers remain on the hive unless you plan to leave them for winter stores.

Take notes on each box position, and mark the hives you moved. During the first warm days of spring you will check on whether your arrangement worked, which helps you improve your technique in later years. See Early Spring: First Inspections and Feeding for the follow-up inspection.

FAQ

When is the best time for a fall inspection?

Early fall, before temperatures drop, while there is still time to feed, treat and combine. A warm, calm afternoon works best.

How many bees should a colony have going into winter?

A strong colony will cover at least eight or nine frames, while colonies with fewer than about five frames in cold climates are at serious risk.

Should I open hives in late fall?

Avoid it. Once temperatures fall and bees form a cluster, opening hives can chill them and break the cluster. Heft and observe from the outside.

Keep learning

Browse all 500 guides →