Beekeeping Directory

Home › Guides › Equipment & Hive Types › Mouse Guards and Entrance Reducers

Equipment & Hive Types

Mouse Guards and Entrance Reducers

Mice are small, determined, and love the warm, dark interior of a winter hive. A mouse that moves into a hive chews comb, fouls stores and disturbs the cluster, sometimes killing the colony. A mouse guard or an entrance reducer, installed before cold weather, is cheap insurance. This article explains how mice invade hives, compares the types of guards, covers entrance reducers and when to use them, gives installation steps, and offers troubleshooting tips. I have made and tested these from hardware cloth, wood and commercial metal strips, and each has quirks worth knowing.

How mice get in

As temperatures fall in fall, mice look for shelter. A standard Langstroth entrance is about 3/8 inch high and roughly the full width of the box, easily wide enough for a mouse. Once inside, a mouse makes a nest in the lower boxes, chewing comb, wax and wood to build it. In winter, a clustered colony cannot defend its territory effectively; bees are sluggish in the cold and the mouse stays warm and well fed on honey and pollen.

Signs of mouse damage include shredded comb, droppings, an odour of urine and a nest of chewed material, usually in the lower boxes. In spring you may find a dead colony, or a weakened one with damaged equipment. Prevention is much easier than cleanup.

Timing

Install mouse protection in early to mid fall, before temperatures drop and mice start to look for shelter. Many beekeepers install them when they finish treatments and fall feeding. Leave guards in place until spring, when bees fly regularly and can defend themselves, then remove them to let foraging traffic flow. Check local advice, since timing differs by region.

Types of mouse guards

Metal entrance reducers with holes. Strips of galvanised steel with 3/8 inch holes, fastened across the entrance. Pros: durable, mouse-proof, can be nailed or screwed on. Cons: bees may crowd the holes, and dead bees can block them.

Hardware cloth. A strip of 1/4 inch or 3/8 inch mesh (check the size so a mouse cannot squeeze through, and that bees still can) bent into a shape and fastened over the entrance. Pros: cheap, flexible. Cons: needs careful fitting, and cut edges are sharp.

Wooden entrance reducers with drilled holes. A block with several 3/8 inch holes. Pros: easy to make, and they work. Cons: wood can be chewed, and moisture may swell it.

Plastic reducers or guards. Pros: lightweight, easy to fit. Cons: plastic can be chewed; may be less durable.

Whatever you choose, the openings must be small enough to exclude mice but large enough for bees to pass. Holes about 3/8 inch work for most mice, but young mice can sometimes squeeze through larger openings, so check your equipment closely.

Entrance reducers

An entrance reducer is a piece of wood or metal that narrows the hive entrance. It is not always mouse-proof, but it serves several purposes:

  • Reducing the entrance in winter to limit draughts and cold air.
  • Helping a small colony defend itself against robbers and wasps.
  • Controlling traffic in a new colony or a nuc.
  • Making mouse protection easier, since a smaller opening is easier to guard.

Most reducers have two notches: a small one for winter and a larger one for summer. A reducer set to the smallest notch can be blocked by dead bees in cold weather, so check it. Some keepers combine a reducer with a mesh guard for added protection. For robbing, a reducer is the first defence; see Robbing Screens: Installation and Use and Robbing Behavior: Prevention and Response.

Installing a mouse guard

  1. Clean the entrance. Remove debris and dead bees.
  2. Check the bottom board. Seal gaps larger than 3/8 inch elsewhere in the hive, such as holes in boxes or ill-fitting joints.
  3. Position the guard over the entrance with the holes or mesh facing outward.
  4. Fasten it securely with nails, screws or staples, so it cannot be pushed aside.
  5. Check the fit. No gap should be big enough for a mouse; hold a pencil beside the opening to test.
  6. Monitor through winter, brushing away dead bees and snow from the entrance.

If you use a reducer, set it to the smaller opening and confirm bees can pass. For more on getting hives winter-ready, see Preparing Your Hive for Winter: First-Year Edition and Winterizing Hives: Insulation and Ventilation.

Dead bees and blocked entrances

In winter, bees die and are carried out, but sometimes dead bees pile up at the entrance and block it, especially when a mouse guard has small holes. A blocked entrance can trap the cluster and suffocate it. Check the entrance on mild days and clear it with a wire or thin stick. Keep snow from blocking it. Having an upper entrance, such as a small hole in a box, gives bees a fallback ventilation and exit route; see Winter Covers and Insulation Kits.

Other pest considerations

Mice are not the only winter pests:

  • Shrews can enter holes mice cannot.
  • Skunks scratch at the entrance at night in some regions, and may need an elevated stand or a barrier.
  • Birds such as woodpeckers can peck through hive walls in some climates.
  • Wasps and hornets might enter weak colonies in warm spells.

Hive stands lift hives off the ground and help reduce access by some pests; see Hive Stands: Why You Need One and How to Build It. In areas where bears are present, fencing is an additional requirement and should be planned early.

Stored equipment is a mouse target too

Mice do not only invade active hives. Stacks of spare supers, drawn comb and frames stored in a shed or garage make perfect winter housing, and they will chew foundation, nest in the frames and foul the wax. Store spare boxes stacked tightly on a solid floor with a cover on top and any entrances closed with mesh, or hang frames in sealed containers. Keep stored comb off the ground, and check for droppings in fall. Use traps rather than poison near stored equipment, so bees and honey are never exposed to chemicals, and follow local rules on rodent control.

Common mistakes

  • Installing guards too late, after mice have moved in.
  • Using wide mesh that mice can squeeze through.
  • Forgetting other gaps, such as upper entrances or holes in old equipment.
  • Leaving guards on in spring, which blocks foragers and pollen traffic.
  • Letting dead bees block the entrance without checking.
  • Using treated lumber or chemicals inside the hive.

FAQ

When should I put on mouse guards?

Install them in early to mid fall, before the first hard cold, and remove them in spring once the bees are flying regularly.

What size holes keep mice out?

Openings of about 3/8 inch are standard, but check your equipment carefully, since small mice can sometimes pass through larger gaps.

Is an entrance reducer the same as a mouse guard?

No, a reducer narrows the opening but may still admit mice unless it is designed with small holes or combined with mesh.

Keep learning

Browse all 500 guides →