Beekeeping Directory

Home › Guides › Hive Management by Season › Adding Supers: Timing and Configuration

Hive Management by Season

Adding Supers: Timing and Configuration

Adding a super is simple in principle: put an empty box on the hive so the bees have somewhere to store nectar. In practice, the timing and configuration decide whether you harvest a crop, lose bees to swarming, or end up with half-filled boxes of uncapped nectar. This article covers when to add the first super, how many to add, how to arrange drawn comb and foundation, whether to use an excluder, and how to manage supers through the flow, with attention to the choices that experienced beekeepers make differently from beginners.

When to add the first super

The signal is not a date but the state of the colony and the flow. Add the first super when the brood boxes are mostly full of bees, comb in the top brood box is filling with nectar, and flowers are blooming that yield nectar in your area, such as dandelions, fruit trees, clover or locust. A rule of thumb is that when the top brood box is about 70-80% covered with bees and brood, you should add space.

If you wait until bees are clustering outside and burr comb is appearing, you have waited too long, and swarming risk has risen. Adding too early is much less of a problem than adding too late, though extra empty space can make it harder for a small colony to heat the hive. Our beginner article When to Add Your First Super explains this in more detail for new beekeepers.

Choosing the super size

Supers come in deep, medium and shallow depths. A full deep super of honey weighs up to 80 pounds, while a medium weighs around 50 and a shallow around 40. Many beekeepers standardise on mediums for supers so that boxes are lighter and interchangeable. See Deep vs. Medium vs. Shallow Boxes for a full comparison.

Whichever size you pick, keep equipment uniform within the apiary if you can. Mixing sizes complicates swapping frames between colonies and makes inventory hard. If you plan to produce comb honey, shallow supers with special frames are often used; see Comb Honey Production. For extracted honey, drawn comb is a major asset because the bees can fill it quickly.

Drawn comb or foundation

Drawn comb is worth its weight in gold. Bees must consume a lot of honey to make wax, with estimates often cited at several pounds of honey per pound of wax, so a flow spent drawing comb produces less honey. A first-year colony with foundation may draw out a super or two and store little surplus. A colony with drawn comb can fill it in days.

When using foundation, add one super at a time, ideally in the early flow, and put one or two drawn frames in the middle to encourage bees to move up. Keep an eye on the pattern, since bees tend to draw the middle frames first. Rotate frames as needed so that outer frames are drawn. See Wax Foundation vs. Plastic Foundation and Foundationless Frames: Pros and Cons for the options.

How many supers and when to add more

During a strong flow, a strong colony can fill a super in a week. A good rule is to add another super when the existing one is about two-thirds full or when the bees have started to cap the middle frames. If you wait for it to be full, the bees run out of storage space and may slow foraging or swarm.

Some beekeepers add supers on top (top supering), while others add them under, just above the brood nest (bottom supering), so that bees draw new comb in the most accessible place. Bottom supering encourages bees to move up and may reduce congestion, though it can also let nectar be placed in the brood area if no excluder is used. Both have advocates; choose one and observe results. In most regions the average strong colony needs two to four supers during the main flow, but check local conditions.

Excluders and brood nest control

A queen excluder keeps the queen from laying in supers, so honey frames contain no brood. Some beekeepers use them routinely, others never. If you use one, put it between the top brood box and the first super, and make sure that the bees have been given room in the brood nest. Fuller discussion appears in Queen Excluders: Pros, Cons, and Proper Use and Queen Excluders: Metal vs. Plastic.

Be aware that an excluder can slow bees' movement to the supers. One trick is to leave the excluder off until bees have started drawing comb in the super, then add it. Another is to place a frame of brood above the excluder to encourage bees to move up. If you notice brood in supers, you can put an excluder under it and wait for the brood to emerge before harvesting.

Super configuration and ventilation

Honey ripening needs airflow. Ventilation carries away water vapour that bees evaporate from nectar, so avoid sealing supers tightly during a heavy flow. An upper entrance or a slightly cracked inner cover can help, as long as the colony can defend it. Hot weather requires shade and enough room that bees do not beard heavily; see Early Summer: Peak Forage Management.

Keep supers level and on a stable stand. A heavy tower of honey is a hazard if the hive tilts or the wind topples it. If you use a hive stand, check that it is solid; see Hive Stands: Why You Need One and How to Build It. Use a strap if your site is exposed.

Monitoring and pulling supers

During the flow, check the supers every week or so. Note how many frames are drawn, how much nectar is being stored, and how much is capped. Do not harvest until frames are mostly capped, or moisture has been tested with a refractometer, as explained in Honey Moisture: Why 18% Matters. Nectar with too much water will ferment.

When the flow ends, take off supers promptly, because bees may begin to move honey down into the brood area. At that point, consider the mite situation, since treatments must not be used with supers on unless labelled for it. Our guide to When to Pull Honey Supers gives a full harvest timeline.

Quick reference

  • Add the first super when bees cover roughly 70-80% of the top brood box.
  • Add another when the current super is about two-thirds full.
  • Put drawn comb in the middle with foundation on the sides.
  • Use an excluder only after bees have moved up.
  • Never feed syrup with honey supers on.
  • Remove supers promptly at the end of the flow.

FAQ

How do I know the bees need another super?

When most frames in the current super are being drawn or filled and bees are crowding the upper boxes. Adding a second super when the first is two-thirds full is a good rule.

Should I put new supers on top or underneath?

Both work. Top supering is simple and keeps honey away from brood, while bottom supering helps bees move upward. Try each and pick what suits your climate and flow.

Can I use a queen excluder from the start?

You can, but many beekeepers wait until bees have started working the super. An excluder placed too early can cause bees to hesitate and raise swarm risk.

Keep learning

Browse all 500 guides →