A trapout removes a colony from a structure without cutting open the wall. Instead of dismantling the cavity, you install a one-way cone over the main entrance so bees can leave but not return, and give them a new home nearby with a queen or brood to attract them. Over several weeks the foragers move into the new box, the old colony weakens, and the structure can be sealed. Trapouts are slower and less reliable than cutouts, but they spare the building. This article covers when to choose them, how to set one up, how long it takes, and why the method fails when it does.
What a Trapout Does
Foragers leave through the cone and cannot find their way back in. They return to the entrance, find a cone, and cluster outside. If you provide a hive with a queen or frames of brood, the foragers will join it. Meanwhile, the brood in the wall continues to emerge until it runs out, and the queen in the wall eventually dwindles or is left with few workers.
The method depends on the bees' homing instinct and their need for a queen and brood. The goal is to move the foraging force and, ideally, the queen into the box. Many trapouts end with the original queen still in the wall, with a small remnant colony that must be dealt with. For a faster, more complete method, see cutouts.
When a Trapout Makes Sense
Choose a trapout when the structure should not be opened: a historic building, a fragile ceiling, a tall wall, a masonry chimney, or any location where cutting would cause damage or danger. It is also useful when you cannot work at the site for long periods, or when the colony is too defensive for a cutout.
Trapouts are less suitable if the colony has multiple entrances, a very large comb, or a tight structure where bees will find new ways in. They take weeks and need repeated visits. They also do not recover the comb or brood. If speed matters, a cutout is better. Get the homeowner's agreement to a timeline and a fee that reflects multiple visits. See swarm catching for the quicker alternative if bees are only clustering outside.
Equipment and Materials
You will need a one-way bee escape cone made of hardware cloth or screen, usually 1/8-inch mesh, sized to fit over the entrance; a staple gun or caulk; a ladder; a hive box with frames, ideally including a frame of open brood from another colony; and a stand or platform near the entrance. A queen cage with a mated queen helps.
Seal all other openings first. Look for gaps in the siding, around vents and under eaves. Any other exit allows bees to continue to use the colony. Use caulk, foam or screen to close every opening except the entrance with the cone. Check from outside and, if possible, inside. Use bright light at night to find leaks. A thorough job at this stage determines success. See hive tools for general items to bring.
Setting Up the Trap
Install the cone so its narrow end points out and its wide end covers the main entrance with no gaps. The exit hole should be slightly larger than a bee, about 3/16 inch, so bees can crawl out but not back. Secure the cone with staples or sealant.
Place the hive box as close to the entrance as possible, preferably within a few feet, with its entrance facing the same direction. Fill it with frames, including a frame of brood. Add a mated queen in a cage with a candy plug if you want to speed up the process. Feed syrup to encourage the foragers to settle. Keep the box in a safe spot, out of walking paths. The box should be firmly supported on a platform or stand.
What to Expect
The first days: bees will crowd around the cone and cluster on the wall. Many will wander into the new box. After a week or two, traffic in the box increases. After three to four weeks, the brood in the wall will largely have emerged and there will be few young bees to replenish the old colony.
The queen usually stays in the wall. Without foragers she is left with a dwindling population and few stores. If you have given the foragers a queen, they settle there. If you cannot get the original queen, the new box with a purchased queen becomes the new colony. After six to eight weeks, remove the cone and check for activity. If the colony is dead or gone, seal the entrance.
Dealing with Honey and Comb
Whether you cut or trap, the honey and comb remain in the wall. A trapout leaves it. Rob bees from other colonies will find it once the colony weakens, which can cause robbing, and the honey can ferment and run down the walls. This is a serious problem in a house, with staining, odors and pests.
Plan to remove the comb after the colony is dead. This may mean opening the wall anyway, at least partially. Warn the homeowner about the honey and the wax moth risk. Consider an access panel. If you intend only a trapout and not a final cleanout, be honest about the consequences. Seal and clean the cavity to avoid new swarms. See wax moth for related pest issues and robbing behavior.
Why Trapouts Fail
- A second entrance goes unnoticed and the bees keep using it.
- The cone is not tight, and bees re-enter.
- The new box has no queen or brood, so foragers leave.
- A late-season trapout runs into cold weather before the colony is gone.
- The cone allows bees to come back by crawling along the wall.
- The original queen produces a new generation of workers faster than they emerge.
If bees drift back, check seals and the cone. If the foragers refuse to enter the box, give brood or a queen. If the process stalls, combine the colony in the box with another hive and consider a cutout. Many trapouts are really hybrid jobs.
Timing and Season
Start a trapout in spring or early summer, when the colony is building and foragers are active and the weather is warm. A trapout started in fall may not finish before winter, and bees may be too few to form a strong colony in the new box. Avoid the dearth, when robbing is fierce.
Allow at least six weeks, and plan to check weekly. Keep records of the date, the number of bees in the box and any problems. If you find yourself still battling bees after two months, rethink the approach. A properly timed trapout can give you a colony of foragers with a new queen, ready for winter if fed. See spring buildup for seasonal context.
After the Trapout
Once the old colony is gone, remove the cone. Clean any visible wax, and seal the entrance with metal flashing or caulk. Treat the new colony as unknown stock: monitor for mites and disease, requeen if the temperament is poor, and give it time to build before winter.
Be realistic about the result. Trapout colonies are often smaller than cutout colonies because they lack brood and comb. Some beekeepers use trapouts mainly to protect a building and view the bees as a bonus. Discuss expectations with the owner, and keep a record of the work. If you need tools for the next job, see moving hives for how to relocate the new colony.
FAQ
How long does a trapout take?
Typically six to eight weeks, though it varies with colony size, season and how well you seal other entrances.
Do I get the queen in a trapout?
Usually not; the original queen stays in the wall, so most trapouts rely on a purchased queen or brood to establish the new colony.
Is a trapout cheaper than a cutout?
It takes less labor on any given day but more visits, and it does not remove the comb, so total costs depend on the job.