Beekeeping Directory

Home › Guides › Hive Management by Season › Cutouts: Removing Colonies from Structures

Hive Management by Season

Cutouts: Removing Colonies from Structures

A cutout is the removal of an established honey bee colony from a wall, ceiling, chimney, tree or other structure by opening the cavity, taking out the comb and bees and installing them in a hive. It is hard, hot, dusty work, and no two jobs are alike. I have done cutouts from sheds, soffits, hollow trees and the walls of a 1920s farmhouse, and I have learned that the real skill is planning, not cutting. This article covers whether you should take the job, how to prepare, the step-by-step method, how to hive the bees and how to restore the structure so they do not come back.

Decide Whether to Take the Job

Not every colony should be removed by a hobbyist. Look at the site: how high is it, how accessible, how big is the cavity, and what is the structure made of? A colony in a ground-floor wall with an exterior panel is manageable. A colony behind plaster in the second story of an occupied house, or inside a chimney, may need a professional contractor and a lift.

Find out how long the bees have been there. A colony in place for years can have many feet of comb and a huge honey store, and it may be defensive. Ask about pesticide use and prior attempts at removal. Check the type of bees and your region's Africanized status. Get permission in writing from the property owner, and settle fees beforehand. If you are not covered by liability insurance and are unsure of your skill, refer the job to someone who is. See Africanized honey bees before taking on any feral colony in an affected region.

Equipment

A cutout kit includes a full bee suit, veil and gloves, a smoker, hive tools, a pry bar, a hammer, a utility knife, a sharp bread knife or serrated blade for comb, a bee vacuum with gentle suction, buckets with lids, rubber bands or comb frames, spare frames and a hive body, tarps, a ladder, a headlamp, a respirator for dust, and cleanup supplies.

Bring a plan for sealing the entrance afterward: hardware cloth, caulk, flashing and lumber. A strong shop vacuum is useful for loose bees and honey but not for the colony itself. Bring a cooler for brood comb and a bucket of water to rinse your tools. Always have a helper. Hive tools describes what to carry.

Opening the Cavity

Find the extent of the comb by listening, feeling for warmth and using a thermal camera or a stethoscope on the wall. Work from the side that gives you the best access to the brood nest, usually the lowest portion of the comb. Remove siding, trim or drywall in sections and set them aside for reassembly.

Go slowly. Cut or pry panels in a way that avoids crushing bees. Expect a cloud of bees once the comb is exposed. Smoke lightly, but smoke alone will not hold a colony; some bees will fly and cluster nearby. A homeowner who has left the area during the process helps everyone's safety. As you open the wall, look for the brood nest, which will be the largest, darkest comb, often in the center. Honey comb is usually above and to the sides.

Removing the Comb

Remove comb in order, from the outer edge toward the center. Cut the comb free from the attachment points. Keep the orientation of brood comb: tag the top. Set the best brood comb aside to tie into frames. Honey comb can be put in buckets, but do not feed it back to your bees; it may contain pathogens.

Cut brood comb to fit your frames and secure it with rubber bands, string or commercial comb holders. Place the brood frames in the hive box with the queen and nurse bees. Use a brush or a gentle vacuum to move bees. You may need hours to find the queen. Drop the comb quickly and avoid squishing bees; crushed bees release alarm pheromone and can turn a calm job into a fight. See finding the queen for tips.

Collecting the Bees

Use a gentle bee vacuum or brush bees into a box. Place a frame of brood in your hive box near the cavity so foragers can find it. Many cutout beekeepers leave the box in place until dusk, so returning bees can enter. Take the bees to your yard after dark.

If you cannot find the queen, leave the box until the next day and check for clustering. A cluster at the box entrance often indicates the queen is inside. If a colony remains in the structure after you leave, you may need to return. Keep an eye out for robber bees attracted by exposed honey; clean the site and seal the area.

Cleaning and Sealing the Site

This is the part that decides whether you will be back. Remove all comb and wax residue, because the scent will attract new swarms for years. Wash the cavity with a mild detergent or a scent neutralizer. Fill the void with insulation or foam and seal every entry point with metal flashing, hardware cloth or caulk.

Reassemble the wall, or leave it for the homeowner's contractor. Make sure there are no gaps larger than a quarter inch. Explain to the owner that a vacant cavity is a lure. Many removals fail because nobody closed the original entrance, and the next swarm moves in. Refer to bait hives for why old comb scent attracts bees.

Hiving and Aftercare

Set the colony up in a hive with the best brood frames and the queen. Feed one-to-one syrup. A cutout colony has lost foragers, comb and often the queen, so it needs support. Reduce the entrance. Keep the hive at least two miles from the original site, or foragers will return to the old location.

Check for the queen after a week, looking for eggs. If there are none, give a frame of eggs from another colony or requeen. Monitor for varroa and disease, as feral colonies are unknown. American foulbrood and other diseases can lurk in old comb. If you find symptoms, call your state apiary inspector. Use fresh foundation as soon as possible and replace the cutout comb within a season. See varroa monitoring and old comb.

Safety and Liability

Wear full protection. Ladders and heights are dangerous, so use proper ladders and safe working methods. Wear a respirator if there is dust or mold. Watch for electrical wires in walls, plumbing and structural members. Do not cut into wiring or load-bearing framing. If the structure is old, assume lead paint and asbestos may be present, and protect yourself and the owner.

Carry liability insurance if you do this regularly. Have a written agreement with the owner stating what you will do, what you will not do and who is responsible for repairs. Be clear about fees. Hobbyists often undercharge. Have an epinephrine plan if any helper is allergic; see safety first for general field safety.

When Not to Cut

Sometimes a trapout is a better choice: if the structure is fragile, historically valuable or hard to open, a slow removal of bees without opening the wall can work. See trapouts. If the colony is huge, defensive or in a dangerous place, call a professional or the local fire service. Do not attempt a job that exceeds your equipment or experience.

Some cutouts are tempting because they look like free bees. But feral colonies often carry heavy mite loads, and the work is exhausting. Treat cutouts as a service and a learning experience first, and as a source of bees second. Start by assisting a skilled cutout beekeeper before you try one alone.

FAQ

How long does a cutout take?

A small colony in an accessible wall can take two to four hours, while a large, old colony may take most of a day or require a second visit.

Will the bees come back after a cutout?

They can if comb scent remains or the entrance is not sealed, so remove all wax and close every opening.

Can I keep the comb from a cutout?

Brood comb can be tied into frames, but old comb may carry disease, so many beekeepers replace it with new foundation after the colony is established.

Keep learning

Browse all 500 guides →