Beekeeping Directory

Home › Guides › Equipment & Hive Types › Solar Wax Melters

Equipment & Hive Types

Solar Wax Melters

A solar wax melter is a glass-topped insulated box that turns sunshine into a quiet, free beeswax processor. You put old comb, cappings and scraps inside, and the sun melts the wax, which runs through a screen and drips into a mold. It cleans wax better than most beginners expect and costs almost nothing to run. This article explains how a solar melter works, how to buy or build one, how to use it safely and how to get clean blocks of wax, along with the limits that make it a supplement rather than a complete wax setup.

How a solar melter works

A solar melter is basically a small greenhouse. Sunlight passes through a glass or clear plastic lid, warms a dark interior and gets trapped by the insulated walls. Beeswax melts at roughly 143 to 151 degrees Fahrenheit, and a good melter on a sunny day can reach 160 to 200 degrees inside, easily enough to liquefy wax without scorching it.

Wax melts and flows down a sloped tray, passing through a screen or cloth that catches propolis, bee parts and cocoons. It then drips into a collection pan, usually sitting in the lower part of the box, where it cools into a block. Debris, called slumgum, stays on the screen.

Because the heat is gentle and gradual, wax does not overheat, and colour stays light. Cappings wax melted this way is often bright yellow and ideal for candles and cosmetics, as in Beeswax: Harvesting and Cleaning and Beeswax Candles: Making and Molds. The same simplicity makes solar melters a favourite for small apiaries and school projects.

Parts of a solar melter

Every design has the same core parts. The outer box is insulated wood, with foam or other insulation in the walls to hold heat. A glazed lid, often double glazing, lets light in while reducing heat loss. A dark metal tray, often painted flat black or made of stainless steel, absorbs light, and a screen or filter sits over it. A catch pan, often a loaf pan or silicone mould, collects melted wax.

The tray should slope slightly toward the front so molten wax flows to the screen. A tilt of a few degrees is enough. A reflector on the lid or sides can increase heat, and some designs add a hinged top to adjust the angle toward the sun.

Ventilation is minimal on purpose, but a tight lid also helps keep bees and wasps out. Gaps invite them, because the smell of warm wax and honey attracts them quickly. See Robbing Behavior: Prevention and Response for why sealing matters. Good gaskets and a clear closing latch save frustration.

Buying versus building

Ready-made solar melters from beekeeping suppliers cost from modest to substantial amounts and ship flat or assembled. They are well insulated, sized for typical use and often come with a tray and screen. Buying suits beekeepers who want a reliable unit without workshop time.

Building your own is a classic woodworking project. A basic box needs plywood or cedar for the shell, rigid foam board for insulation, a pane of glass or twin-wall polycarbonate for the lid and black-painted sheet metal for the tray. Hinges, a latch and weatherstripping finish the job. Plans are widely available from clubs and extension offices.

Use safe materials. Keep treated lumber and non-food-safe paints away from surfaces that touch wax, and use heat-resistant black paint rated for food contact, or bare stainless steel. Glass can break, so use tempered glass or acrylic for safer handling. If building with kids, adults should handle saws and sharp tools, and the project is a good fit for 4-H, as described in Making Beeswax Crafts: 4-H Project Ideas.

Using the melter step by step

Choose a spot with full sun and shelter from wind. Face the glass toward the sun, tilting if you can. In northern latitudes, the best melting occurs on clear days from late spring to early autumn.

  1. Clean the interior and put the screen or filter cloth in place.
  2. Place the clean mould or pan under the drip point.
  3. Load cappings, scraps or old comb in a thin layer over the screen, because thick piles melt slowly.
  4. Close the lid, secure it and check that no gaps exist.
  5. Let the sun do its work, checking every few hours.
  6. When the wax stops dripping, remove the mould, let it cool, and clean out the slumgum.

Do not overload the tray. A thin layer melts faster and gives cleaner wax. Add more after the first batch is through. In weak sun or cool weather, give the melter longer or cover it with a blanket to hold heat.

Getting cleaner wax

A solar melter filters as it melts, but you can improve results further. Use a fine filter, such as a layer of cheesecloth or a paint strainer, over a coarse metal mesh. Replace the cloth each batch.

Pre-clean the material. Rinse cappings to remove honey and let them dry first, or let them drain in a tank overnight. Honey in the wax can caramelise and darken it. Old dark comb contains cocoons and propolis, which produce darker wax and more slumgum. Keep cappings separate from old comb if you want light wax.

Re-melt blocks in a double boiler with a bit of water for a second purification. Allow the wax to cool slowly in an insulated container so impurities settle to the bottom, and scrape the dirty layer off the underside. For more advanced rendering, see Beeswax Processing Equipment.

Limits and cautions

A solar melter is excellent for small amounts, but it has limits. Output depends on weather, season and sun angle, and cloudy weeks may produce nothing. Old brood comb contains a lot of cocoon material that absorbs wax, so yields from dark comb can be low, and a solar melter leaves much wax in the slumgum.

Pests are a risk. Wax moths and small hive beetles can reach exposed material, so process comb quickly and keep it covered. See Wax Moth Control in Storage. Wasps and bees also find the odours, so keep the melter closed and avoid leaving honey nearby.

Avoid melting comb from hives with diseases like American foulbrood in a way that spreads spores. Wax rendering does not reliably destroy spores, and equipment like frames may need handling according to local regulations. Ask your state apiarist or extension office how to handle diseased comb, and follow local law.

Fire and burn safety

Although solar melters use only sunlight, internal temperatures can pass 200 degrees Fahrenheit and burn skin. Wear gloves when removing hot pans. Melted wax can ignite if overheated, so never heat wax with a flame or direct heater to speed the process.

Keep the melter on a non-flammable surface away from dry grass and wooden walls, since concentrated sunlight through glass and reflectors can scorch surfaces. Do not leave it unattended in extreme heat if parts are plastic that might deform. Never cover the top with dark cloth that could trap too much heat.

Supervise children, as lids may be hot and glass may break. Check that hinges and latches hold in wind, since a falling lid can shatter glass. Safety rules also apply to any later wax work indoors, as in Beeswax Lip Balm and Salves.

Care and storage

Clean the melter after each season. Scrape slumgum from the screen and wipe the tray with a dry cloth. Do not use soap or water, which can leave residues. Warm the tray in the sun to soften sticky wax and wipe it out with paper towels.

Inspect the seals and glass, repair cracks and replace worn weatherstripping. Check for rust on metal trays. Paint the exterior with exterior latex in a light colour to protect wood and reflect heat, and keep paint off the interior.

Store the melter in a dry place over winter, or cover it so snow does not collect on the glass. Keep spare screens and moulds with it. A well-kept solar melter lasts for many years, and you can scale up to other equipment as your wax output grows.

FAQ

How hot does a solar wax melter get?

A well-insulated unit in full sun commonly reaches about 160 to 200 degrees Fahrenheit, which is above beeswax's melting range of roughly 143 to 151 degrees. Cloudy or cold days may not melt anything.

Can I melt old brood comb in a solar melter?

Yes, but yields are low because cocoons absorb wax, and the wax is darker. Use cappings for clean light wax and treat old comb as a lower-grade product. Follow local rules for comb from diseased colonies.

How do I keep bees and wasps out of the melter?

Use a tight-fitting lid with weatherstripping, keep seams sealed and avoid leaving honey outside. Process material quickly so the smell does not draw pests.

Keep learning

Browse all 500 guides →