Section comb honey is the oldest form of comb honey: small, square, basswood boxes filled by the bees with fresh white comb, capped and sold whole. It was the standard for generations before the extractor became common, and a few producers still make it for the premium market, county fair entries and sheer craftsmanship. I started with sections as a young beekeeper and still run a few supers each year. They are fussy, but they are beautiful. This article covers the equipment, preparation, management, harvest and troubleshooting of section honey. See comb honey production and managing for comb honey production for the general principles.
What Sections Are
A section is a small wooden box, traditionally about four and a quarter inches square, designed to hold a single piece of comb weighing roughly a pound or slightly less, with a thin sheet of foundation in the middle. Sections are held in a rack or frame called a section holder, which sits in a super. The bees fill the box and cap it. Each section is then removed and wrapped.
Sections were once made of basswood, which is light, white and bends without breaking; modern sections may be plastic or wood. The traditional super holds about 24 sections. The product is sold as a whole piece, without cutting. Because the box defines the shape, it requires less handling after harvest than cut comb, but more preparation before.
Equipment
You need section supers, section holders, sections, foundation, a fold-and-assemble jig, a foundation fastener, separators (sometimes called fences or slats), bait sections and packaging. Sections come flat and must be folded and glued or held together. Foundation is fastened into the section, either with wax or with a fastener.
Thin comb-honey foundation is essential. Fill the section nearly to the top with foundation, leaving a small gap at the bottom. Some beekeepers use full sheets and some use starters. Avoid wired foundation. Equipment can be found at specialty suppliers and from other beekeepers. Many sizes exist, so make sure your parts match. See DIY versus commercial equipment for sourcing ideas.
Preparing Sections
Assemble sections in advance. Wet the bends in the wood if needed, fold them and fit them together. Fasten foundation carefully, centered and straight. Warped foundation leads to crooked comb. Load sections into holders and place them in the super, with separators if your system uses them.
Fill one or two sections with drawn comb from the previous year, as bait. These draw the bees up into the super and encourage them to work the rest. Keep assembled supers clean and out of dust. Do not touch the foundation with greasy hands. A well-prepared super will draw faster and give more even results. Note which colony each super goes to, and record dates.
Management During the Flow
Place section supers on strong colonies just as the flow begins. Colonies must be crowded to work them. Many beekeepers put a section super over a colony already working in a deep or shallow super, so bees move up once the lower super is filled. Others use a small hive body to concentrate bees. A queen excluder prevents brood.
Check often. Bees tend to fill the center sections first and neglect the corners. Rotate sections by moving outer ones to the center when the middle sections are nearly finished. Remove finished sections quickly, before travel stain darkens the cappings. Watch for swarming; a crowded colony in a heavy flow is an ideal swarmer. See swarm season.
Flow and Floral Source
Sections need a strong, sustained flow. Clover, basswood and black locust all produce light, attractive combs, and have long been favorites. Late flows such as goldenrod or aster produce darker honey, and the honey may granulate in the comb. The area must also be free from interrupting dearths, which cause bees to chew or discolor cappings.
Match your timing to the flow. Learn your local flows, and keep records. If your area has a short or erratic flow, sections may not be practical. Many beekeepers produce only a few supers each year. See basswood and black locust and canola and clover.
Harvest and Finishing
Remove sections when they are fully capped, or nearly so. Cappings should be white and even. Brush off bees gently, and carry sections in a covered container. Scrape propolis off the wood with a thin knife. Clean the edges, and sort by weight and appearance.
Freeze the sections for several days to kill wax moth eggs, then wrap and store. Use cellophane or clear plastic wrappers, and label with weight, producer, name and address. Check local laws, as comb honey is usually sold by net weight and must be labeled. Keep sections cool and dry. See wax moth in comb honey and honey labeling requirements.
Troubleshooting
- Bees ignore the sections: the flow is weak, the colony is not crowded or the supers went on too early.
- Comb is built crooked: foundation was not straight or the super was not level.
- Cappings are dark: sections stayed on too long or the colony had propolis problems.
- Sections are partly filled: the flow ended; sell these as chunk honey or extract.
- Brood in sections: no excluder was used.
Most issues come from timing and colony strength. Keep records and learn from each season.
Using Partly Filled Sections
Not every section will fill. In most seasons you will have a pile of partly drawn or partly capped boxes at the end of the flow. Do not waste them. Fully capped sections go to market. Sections with a few uncapped corners can be cut out and packed as chunk honey, or placed back on a hive the next season as bait sections, since drawn comb draws bees upward. Sections with only a skin of wax and no honey can be stored frozen and reused, which gives the bees a head start in next year's flow.
Sort sections at harvest into three piles: premium, standard and bait. Weigh premium sections to be sure they meet a consistent net weight, since customers expect a uniform size. Keep the bait sections wrapped and frozen until spring, then thaw and place a few in the center of each super. Handle bait sections cleanly, because propolis and dirt make bees less eager. Treat a section like a small piece of furniture: well made, carefully finished, and never rushed. This sorting also gives you honest data on how many sections filled per colony, which guides your decisions about how many supers to prepare next year.
Showing and Selling
Section honey is a favorite for fairs. Judges look at uniform capping, full sections, no leaks, clean wood and consistent weight. See comb honey judging standards and preparing a 4-H exhibit.
For sale, market the product as a premium gift or specialty. Explain what it is and how to eat it. Because production is limited, set a price that reflects the work. See pricing your honey.
FAQ
How much honey does a section hold?
A standard section holds about a pound or slightly less of comb honey, depending on the size and how fully the bees fill it.
Do I need a queen excluder with sections?
Many beekeepers use one to keep brood out of the sections, though it is not required if the colony is well managed.
Can I reuse sections?
Wooden sections are generally single use, but plastic sections can be cleaned and reused according to the manufacturer.