Beekeeping Directory

Home › Guides › Equipment & Hive Types › Queen Catchers and Marking Tubes

Equipment & Hive Types

Queen Catchers and Marking Tubes

Catching a queen safely is the first step in marking, clipping, caging or moving her, and the tools involved are simple: a clip-style queen catcher, a push-in cage, or a marking tube with a plunger. Used well, they let you hold a queen without touching her. Used badly, they can injure or lose her. This article compares the common devices, describes how to use them step by step, explains what makes each design safer, and offers tips for beginners who are nervous about handling the most valuable bee in the hive.

Why use a catcher at all

A queen is fragile, fast and surrounded by workers. Picking her up with your fingers risks crushing her or damaging her legs, and bees can sting you in the process. A catcher or tube lets you hold her briefly, mark her, clip her wing, or move her into a cage with minimal contact. It also reduces the temptation to squeeze.

Some experienced keepers do hold queens by the thorax with gentle fingers, but a tool is safer for beginners and for anyone working with expensive or irreplaceable queens. Learn to find her first with Finding the Queen: Tips for Beginners.

Clip-style queen catchers

These are plastic or metal clips with two jaws and slots that let bees move through while holding the queen by her body. A typical catcher looks like a spring-loaded hair clip with narrow bars.

Benefits:

  • Quick and easy to use with one hand.
  • Gentle grip, no direct handling.
  • Reusable and inexpensive.

Drawbacks:

  • If you press too firmly, you can crush the queen.
  • Workers may sneak out through the slots.
  • You must be precise about positioning.

To use, approach the queen from the side, slide the open clip over her, and gently squeeze closed. Release the clip slowly if you drop her. Some designs allow you to open the jaws to hold her briefly for marking.

Push-in cages

A push-in cage is a small square of wire mesh, with an open bottom, that you press into the comb over the queen to trap her. It is used for isolating a queen on a frame, holding her while workers accept her, or restricting her movement. It is not a catcher in the strict sense, but it is a very useful tool.

Benefits:

  • No handling at all; the queen stays on the comb.
  • Gives workers time to accept a new queen.
  • Easy to make from hardware cloth.

Drawbacks:

  • You must be careful not to crush bees, eggs or brood beneath the mesh.
  • The queen may be harassed if you press it onto a frame with a lot of bees.

See Queen Introduction: Direct vs. Cage Methods for how push-in cages are used when introducing a new queen.

Marking tubes

A marking tube is a clear tube with a foam plunger. You place the tube over the queen on the comb, nudge her into the tube, then gently push the plunger to hold her against the mesh so you can apply paint. After marking, you release her back onto the comb or into the hive.

Benefits:

  • Very gentle grip; the queen is pressed softly against foam.
  • Clear view of her thorax.
  • Easy to control for beginners.

Drawbacks:

  • Wrong pressure, either too hard or too soft, can hurt or lose her.
  • The tube must be positioned carefully.
  • Paint must dry before release.

For marking methods, colours and the year code, see Queen Marking: Colors and Methods.

Step-by-step: catching a queen with a tube

  1. Prepare. Have your tube, plunger, paint pen and a clean frame ready. Work calmly, with minimal smoke.
  2. Find the queen. Lift the frame and confirm her location.
  3. Place the tube. Hold the frame at an angle and lower the open end over her, resting it flat on the comb.
  4. Guide her in. Gently coax her to walk up into the tube, without squeezing.
  5. Insert the plunger. Slide the foam in until it touches her lightly, so she cannot move.
  6. Mark. Apply a small dot to her thorax, avoiding the head, wings and legs.
  7. Release. Let the paint dry briefly, then hold the tube against the comb and withdraw the plunger so she walks out.
  8. Return the frame. Replace it gently and close the hive.

If she runs or flies, do not chase. Replace the frame, close the hive, and try again later.

Safety for the queen

  • Never press hard. Even soft foam can crush if you squeeze.
  • Avoid lingering; a queen held too long can overheat or be injured.
  • Work in mild weather and avoid wind.
  • Be patient; find her calmly.
  • Do not catch her over the ground, where she can fall and be lost. Work over the hive or a frame holder.
  • If she is dropped, stop and retrieve her gently.

If you lose a queen, check the area, and look in your clothing and the grass. Queens often cling to the bottom of a box or climb on your veil.

Choosing and maintaining tools

Pick a catcher that suits your hand size and experience. Beginners often find tubes easier than clips. Rinse and dry tools after use, and replace foam plungers when they become hard or sticky. Keep spare tools in your kit. Clean them between colonies to reduce disease risk.

Beyond catching, consider related tools such as Queen Clipping: Technique and Controversy, Marking and Tracking Queens and Queen Rearing Equipment: Grafting Tools and Cells. For general tools, see Hive Tools: J-Hook, Auto-Rotate, and Standard.

Building a simple kit

A basic queen-handling kit is cheap to assemble and fits in a small box that rides in your truck or tool bag:

  • One clip catcher and one marking tube with spare foam plungers.
  • Two push-in cages, one of them homemade from hardware cloth with a securely folded edge.
  • A paint pen or marking set in this year's colour; see Queen Marking: Colors and Methods.
  • Small sharp scissors, if you clip, kept clean and in a protective sleeve.
  • A soft cloth for wiping tools and a small container for rinse water.
  • A queen cage with candy for emergencies, for example if you find a queen in poor condition.

Keep everything in one place so you are not hunting for items with an open hive. Practise on drones first, which are bigger, slower and do not matter to the colony. Rehearse the sequence before you open the hive: find, secure, mark, release. A calm, rehearsed routine is the best protection for a queen.

FAQ

Is it safe to use a queen catcher on a valuable queen?

Yes, if you use gentle pressure and practise on a less valuable queen first; most injuries come from squeezing, not from the tool itself.

How do I keep a queen from flying away during marking?

Work close to the hive over a frame or box, avoid windy days, and hold her gently; if she takes off, stay still and watch where she lands.

Do I need a marking tube if I can hold a queen by the thorax?

A tube is gentler and more reliable for beginners; experienced keepers may hold queens by hand, but any method requires care.

Keep learning

Browse all 500 guides →