Beekeeping Directory

Home › Guides › Honey & Hive Products › Extracting Honey: Step by Step

Honey & Hive Products

Extracting Honey: Step by Step

Extracting honey means spinning the honey out of uncapped frames with centrifugal force while leaving the drawn comb intact for reuse. Done well, it is a fast, clean process that yields honey ready to strain and bottle; done badly, it breaks comb, wastes honey and creates a sticky mess. This article lays out the full process from preparing the room to cleaning up, with attention to extractor loading, spin speeds, temperature, food safety and the usual traps. It focuses on radial and tangential extractors common in small operations.

Before you spin: room and gear

Set up in a clean, dry, bee-tight space with washable surfaces. A garage, a basement kitchen or a dedicated honey house all work, as long as you can keep it clean and keep out pests and pets. Cover or move anything you do not want sticky.

Warm supers ahead of time, ideally in a room at 80-90°F (27-32°C) for several hours or overnight. Warm honey flows quickly, and cold honey leaves more behind. Wash equipment before use and dry it, because water introduced into honey raises moisture.

Gather the following:

Read Extractor Types: Tangential vs. Radial and Manual vs. Electric Extractors if you are still choosing equipment.

Balancing and loading the extractor

An unbalanced extractor will walk across the floor and may damage itself or injure you. The goal is to load frames of similar weight opposite each other.

In a tangential extractor, frames sit with one face outward. You spin one side, flip frames and spin the other, which is slower but gentle on wide or fragile comb. In a radial extractor, frames sit like spokes, with the top bar outward, and both faces empty at once. Radial machines are efficient for many frames, though they need a good gate-and-bucket setup and may stress heavy frames.

Place frames of similar weight opposite each other. If you have an odd number, add a dummy frame or a frame of similar weight. Check that the lid fits and that the machine is secure before turning it on.

Never put hands near a spinning extractor and never leave children unsupervised near it. Wait for the drum to stop completely before opening the lid.

The spin: speed, time and technique

Start slowly. A fast spin of a heavy frame can blow out the comb, particularly new, fragile comb. The first spin should be gentle to remove roughly half of the honey. Then flip frames (in a tangential machine) and spin the other side, and finish with a faster spin to clear the remainder.

Typical time is several minutes per stage, but exact settings depend on the extractor, the comb and the honey. Let the honey show you what to do: if it flows steadily down the drum wall and out the gate, you are fine, and if the flow slows to drips, the frames are nearly empty.

Use a hand crank or an electric motor with a speed control. Manual machines give you a feel for the load; electric machines save effort at volume. Do not spin frames so fast or so long that you damage the comb; drawn comb is valuable.

Handling honey as it flows

Open the gate and let honey run through a coarse strainer into a bucket. Keep the strainer clean; wax particles and bee parts clog it quickly. Switch strainers when the flow slows and rinse coarse strainers with warm water, not into honey you intend to sell.

Fill buckets only part way so they are easier to lift and so foam can settle. Cover buckets promptly with lids to keep out dust and insects. Let honey stand for a day or two so air bubbles and fine wax particles rise to the surface; skim these off before bottling. See Filtering Honey: Strainer Sizes for strainer sizes and Bottling Honey: Food Safety and Best Practices for the final step.

Check moisture before bottling: if honey measures above about 18.6 percent, it is at risk of fermenting, and you may need to dry it or label and sell it for immediate use; see Honey Moisture: Why 18% Matters.

Dealing with problems

ProblemLikely causeFix
Extractor walking or shakingUnbalanced loadRebalance or add dummy frames
Comb breakingSpinning too fast or comb too newStart slow, use tangential spin first
Honey too thickCold honey or cold roomWarm supers and room
Honey with foamSplashing or fast flowReduce spin speed, lower the gate flow
Crystals in combHoney crystallized before extractionWarm frames or leave for bees to clean
Unextracted cellsPoor uncappingUncap again before the next spin

If honey has crystallized in the comb, you may not be able to extract it. Return the frames to the bees to move it, or crush and strain the comb. See Crystallization: Causes and Reversal for what causes it.

Food safety and cleanliness

Honey is low in water and acidic enough that most microbes do not grow in it, but it can still be contaminated by dirt, chemicals or foreign material. Treat the extraction space as a food workspace. Wash hands, wear clean clothes, tie back hair and keep pets away.

Use only food-grade containers, and avoid galvanized or reactive metals that contact honey, since honey is acidic and may pick up metals. Stainless steel and food-grade plastic are the usual choices. Do not reuse containers that held non-food materials.

Keep records of date, source and batch, because they help you trace problems and meet any labeling or cottage-food rules; see Honey Food Safety: Infant Botulism Risk and Cottage Food Laws and Honey Sales.

Cleaning up and storing equipment

Clean up while honey is still warm. Scrape wax from the extractor, rinse with warm water and dry thoroughly. A sticky extractor left overnight attracts ants and bees and can ferment. Wash buckets, strainers and tools, and dry them completely before storage.

Return wet supers to the hives in the evening so that the bees can clean the frames, then remove them after a few days and store them dry with moth protection; see Wax Moth Control in Storage. Do not leave wet supers in the garage, because they invite wax moth and robbers.

Record the weight and quality of the harvest for each yard. This record helps you plan next year and tells you which colonies deserve more attention.

Scaling up and sharing equipment

If you only have a few hives, a club extractor or a shared rental is usually the economical choice. Group extraction days are also good for teaching newcomers and 4-H or FFA members, with an adult supervising any powered equipment; see Honey Extraction Day: A 4-H Club Activity.

As you scale, consider an extractor that holds more frames, a sump with a pump, heated tanks and a bottling setup. Each upgrade should solve a real bottleneck, not just add cost. If you intend to sell honey, check cottage-food or honey-house rules in your state before you invest in a permanent space.

FAQ

How warm should honey be for extraction?

A room around 80-90°F (27-32°C) is common. Warm honey flows well, but avoid heating it so much that flavor suffers.

Can I reuse drawn comb after extraction?

Yes. Intact comb returned to the bees is valuable because they do not need to rebuild it, so protect it from damage and pests.

What if my honey is above 18.6 percent moisture?

It can ferment. Reduce moisture if possible with careful drying, or keep it for short-term personal use rather than sale, and test with a refractometer.

Keep learning

Browse all 500 guides →