Beekeeping Directory

Home › Guides › Honey & Hive Products › Filtering Honey: Strainer Sizes

Honey & Hive Products

Filtering Honey: Strainer Sizes

Filtering honey removes wax bits, bee parts and debris so the finished jar looks clean and stores well. It does not make honey safer or purer in any chemical sense; it is a physical clarification step. How fine you filter changes appearance, pollen content, flow speed and shelf life, and it also shapes how a customer perceives raw honey. This article explains strainer and filter sizes, the order of passes, how to handle thick honey and how to keep the setup clean, with attention to the pollen and labeling questions that come up when you sell.

Why filter at all

Fresh extracted honey contains wax flakes, propolis, pieces of bees and microscopic bubbles. Left in, they float to the top and form a scum, make jars look cloudy, and can seed crystallization. Straining removes the larger debris and gives a better finished product.

Straining is different from the industrial process of ultrafiltration, which forces honey through very fine media under pressure and removes pollen entirely. That level of filtration is common in large commercial packing and is a factor in some of the controversy over honey origin; see Honey Adulteration: Detection and Industry Issues. Small-scale straining is far gentler and keeps most pollen.

The aim is a balance: clean enough to look good and bottle smoothly, but not so fine that you lose characteristics your customers may value.

Mesh sizes and what they do

Filter media are described by mesh or micron size. The numbers below are typical ranges rather than rules, and products vary by maker.

StageTypical mesh or mediaRemovesNotes
CoarseRoughly 400-600 micron screenWax chunks, bee partsFirst pass at the extractor gate
MediumRoughly 200-300 micronSmaller wax bitsCommon for bucket-top strainers
FineRoughly 100 micron or finer cloth/nylonFine particles and bubblesSlows flow; warm honey helps
Very fine or pressurizedUnder about 50 micronAlmost all particles, most pollenCommercial; rarely used by small producers

Many small producers run two stages: a coarse strainer on the extractor gate and a finer nylon or stainless filter over the bottling bucket. Check the product details from your supplier, because mesh sizes are sometimes listed in microns and sometimes in mesh count. See Honey Buckets and Filters for equipment choices.

Setting up a two-stage system

A simple setup uses gravity and warmth.

  1. Place a coarse strainer over a food-grade bucket under the extractor gate.
  2. Fill the bucket partway and cover it.
  3. After the extractor is empty, set a second finer strainer over a clean bucket with a honey gate.
  4. Pour the first bucket through the finer strainer, ideally in a warm room.
  5. Let the honey settle for 24-48 hours, then skim the foam and wax from the surface.
  6. Draw honey from the bottom gate into jars or bottles.

Settling does a lot of the work. Bubbles and wax rise slowly in thick honey, and a day or two of rest in a warm room gives a clearer product without needing very fine mesh. See Bottling Honey: Food Safety and Best Practices for the next steps.

Keep honey covered while settling. Open buckets attract dust, insects and humidity, and honey absorbs moisture from damp air.

Warmth, thickness and flow

Thick honey clogs fine screens. Warming honey to roughly 95-105°F (35-40°C) makes it flow faster through filters, while overheating will degrade flavor and delicate aromas. A heated bucket jacket or a warm room is gentler than direct heat. Do not microwave honey in bulk or heat it unevenly.

If honey is crystallizing or very thick, filtering becomes slow. Gently warm it, and consider stopping and returning later rather than forcing it. See Crystallization: Causes and Reversal for what drives thickening and how to reverse it.

Creamed or partly granulated honey cannot be strained through fine mesh at all, which is one reason producers strain before creaming; see Creamed Honey: Making and Marketing.

Pollen, raw labeling and customer expectations

Straining through ordinary mesh retains most pollen, which is why small producers can call honey raw and still strain it. If you filter finer, you reduce pollen and may blur the line between raw and processed honey in the minds of customers. See Raw vs. Pasteurized Honey for how raw is usually understood.

Some buyers see pollen as a mark of authenticity, and some regulators and testing labs use pollen to help identify honey origin. Remember that honey is legally defined differently by region, and rules about labeling and claims vary; check with your state department of agriculture and with Honey Labeling Requirements by State.

Be honest in your marketing. Do not claim that strained honey is unfiltered, and do not claim health benefits of pollen content. The evidence for pollen-based benefits in ordinary honey is limited.

Cleaning and maintaining filters

Wax and sticky residue clog fine mesh quickly. Rinse strainers in warm water as soon as you finish, using a soft brush, and avoid scouring pads that damage the weave. Dry them completely before storing. Nylon and stainless-steel filters can last for years if cared for.

Do not use detergents with strong fragrances on food contact equipment, and rinse thoroughly. Inspect screens for tears or holes, and replace damaged ones.

Honey rinsed from filters is watery. Do not mix it into honey for sale because it raises moisture. Use it for personal use, mead or as bee feed only where appropriate and safe.

Common mistakes

  • Using a mesh so fine that the honey takes hours to pass
  • Straining honey cold, which clogs filters
  • Leaving buckets uncovered
  • Reusing filters that were not washed
  • Overheating honey to speed filtration
  • Making claims about purity or filtration that are not accurate

For most beekeepers, a coarse plus medium pair and a day of settling is plenty. Add finer media only if your customers or competition standards call for it; see Honey Judging: Color, Clarity, and Flavor for how clarity is judged.

Troubleshooting a slow or cloudy result

If honey will not pass through a filter, the cause is almost always temperature or mesh. Check the room first: honey at a cool 65°F (18°C) can be many times thicker than honey at 95°F (35°C). Warm the bucket gently and give it time rather than pushing honey through with pressure, which can tear mesh and force debris through.

If jars come out cloudy after filtering, the haze is usually fine air bubbles or early crystal formation rather than debris. Bubbles clear with more settling time. Early crystals are normal in many honeys and are not a defect, but tell customers what they are seeing. Fine white foam on top of a jar after a few days is usually air that rose after bottling, and it can be avoided by letting honey settle longer and filling jars slowly down the side.

When filtering is part of a bigger system

If you pack for others or sell at scale, review your process under food-safety rules. See Honey Food Safety: Infant Botulism Risk, Co-Packing and Private Label and Selling Honey at Farmers Markets for the rules and the practicalities. A clear, consistent product is easier to sell, and a clean workflow also reduces complaints.

FAQ

Does straining remove pollen?

Ordinary kitchen-scale and beekeeper strainers remove wax and debris but leave most pollen. Very fine or pressurized filtration removes much more.

What mesh size should I use?

A coarse screen followed by a finer one in roughly the 200-300 micron range, plus a day of settling, works well for most small producers.

Can I filter crystallized honey?

Not easily. Warm it gently to liquefy first, or strain before it crystallizes.

Keep learning

Browse all 500 guides →