Beekeeping Directory

Home › Guides › Honey & Hive Products › Cut Comb: Harvesting and Packaging

Honey & Hive Products

Cut Comb: Harvesting and Packaging

Cut comb is the most approachable form of comb honey: you let bees draw and fill a shallow or medium frame with fresh comb, then cut the finished comb into squares and wrap or box the pieces. It needs no extractor and uses mostly standard equipment, but it rewards careful timing, clean wax and neat cutting. This article covers choosing frames and foundation, getting the bees to build well, harvesting, cutting technique, draining, packaging, freezing for pest control and pricing, plus the mistakes that turn a beautiful frame into a sticky mess. It assumes you know basic hive management and have a strong colony going into a flow.

Why cut comb is a good entry product

Comb honey sells at a premium over extracted honey, and cut comb is the least expensive way to produce it. A shallow super of cut comb gives a dozen or more neat squares, and each can be sold individually or packed for gifts. You skip extraction, filtering and bottling, which saves labor and equipment.

The trade-offs are real. Bees must be strong and the flow must be good. Yields per colony are lower than extracted honey because bees use a lot of energy and nectar to build wax. Cut comb also has a short window: it should be harvested as soon as it is fully capped, packaged quickly and sold within a reasonable time. See Comb Honey Production for the bigger picture and Managing for Comb Honey Production for colony management through the flow.

Frames, foundation and setup

Most producers use shallow or medium supers. Shallow frames, about 5 and 3/4 inches deep, give pieces that fit standard containers. Use thin surplus foundation, which has very fine cell walls so the finished midrib is almost unnoticeable, or use foundationless frames with a starter strip of wax.

Assemble frames carefully and avoid wire in the frame, because wire makes cutting difficult and may show in the finished piece. Some beekeepers use unwired thin foundation and support it with wooden frame notches or a split bottom bar. Give the bees clean, new wax rather than reused comb; see Wax Foundation vs. Plastic Foundation.

Keep the super level, because bees build comb to gravity. A level hive stand and plumb frames give straight comb that cuts into regular pieces.

Getting bees to draw and fill comb

Bees draw comb best when they are crowded, the flow is strong and temperatures are warm. A common approach is to place the comb super above a queen excluder and over a partially drawn super, or to place one or two drawn combs among new foundation as bait.

Add the cut-comb super when the colony is busy with nectar. If you add too early, the colony may ignore it and the foundation may be chewed. If you add too late, the flow may end before comb is built. Watch the colony for white wax along frame edges, which means bees are ready to build.

Prevent swarming, because a swarming colony will abandon comb honey; see Reproductive Swarming: Triggers and Sequence. Give plenty of room in the brood area, and consider separate colonies for comb production so you do not need to suppress swarming at the expense of other goals.

Harvesting the frames

Take frames when the comb is fully capped, with at most a small uncapped patch near an edge. Test moisture with a refractometer if possible, and aim for 18 percent or below; see Honey Moisture: Why 18% Matters.

Remove supers promptly after the flow ends, because honey left on the hive darkens from bee traffic and propolis staining. Use bee escapes or a gentle brush, not heavy smoke, which can taint the product. Handle frames carefully to avoid cracking comb; warm comb is soft and fragile.

Move frames to a clean, cool space. Keep them upright and avoid bumping. If you must store frames before cutting, keep them cool and dry, and protect them from wax moth; see Wax Moth in Comb Honey: Prevention.

Cutting technique

Warm, clean, sharp tools make neat pieces. Use a thin stainless knife or a dedicated cut-comb cutter, and keep a pan of hot water for warming the blade, with a towel to dry it between cuts.

  1. Lay the frame flat on a clean cutting board or rack, with a tray below to catch drips.
  2. Remove the frame by cutting the comb off the top bar and the sides with the warm knife.
  3. Lay the comb on a rack and cut it into pieces sized to your containers, usually about 3 by 4 inches.
  4. Trim any damaged edges, and cut around uncapped cells or discolored patches.
  5. Let each piece drain on a rack for a few hours, so cut edges lose excess honey.

Save trimmings for chunk honey or personal use; see Chunk Honey: Comb in Liquid. A grid cutter makes uniform pieces quickly, and a template guides hand cutting.

Packaging and labeling

Place pieces in clear, food-grade clamshells or comb honey boxes. Containers should fit tightly enough that comb does not slide, but not squeeze the comb. Wipe each piece and the container clean before sealing, and use a label with product name, net weight, your contact details and any lot code. Weigh each package. Individual weights differ, so sell by package weight, not by pieces; see Honey Packaging: Jars, Labels, and Branding.

Check state labeling and cottage-food rules, because comb honey may be treated differently from bottled honey; see Honey Labeling Requirements by State and Cottage Food Laws and Honey Sales.

Keep packaged cut comb in a cool place and sell it quickly. Honey drips can accumulate in the container, which is normal but unattractive, so tell customers that some leaking is natural.

Freezing, storage and pests

Freeze finished comb in sealed plastic at 0°F (-18°C) or colder for 48 hours to kill wax moth eggs and larvae, and let it warm slowly before unwrapping so condensation does not form on the comb. Do this before cutting if you can, and again after packaging if you plan to store for a while.

Do not use chemical fumigants on comb sold as food. See Wax Moth Control in Storage for safe options. Store comb honey at cool room temperature in sealed containers. Comb honey may crystallize over time, and crystallized comb is still edible but less appealing; see Crystallization: Causes and Reversal.

Common mistakes

  • Using heavy brood foundation, leaving a thick midrib
  • Leaving supers on too long, causing travel stain
  • Cutting cold comb with a cold knife and cracking cells
  • Skipping the draining step and shipping sticky containers
  • Allowing brood in comb honey frames
  • Selling comb with uncapped, wet cells

Start with a few frames and refine your process. Compare results year by year, and keep notes on which colonies and which flows give the best comb.

FAQ

Do I need special equipment to make cut comb?

Not much. Thin foundation or starter strips, a sharp warm knife, a draining rack and clear containers are the basics.

Why is my cut comb dark?

Comb darkens from bee traffic and age. Use fresh foundation and harvest promptly after capping.

Can I sell cut comb in a home kitchen?

It depends on state law. Check cottage-food and honey rules with your state agency before selling.

Keep learning

Browse all 500 guides →