Beekeeping Directory

Home › Guides › Equipment & Hive Types › Frame Types: Wood, Plastic, and Foundationless

Equipment & Hive Types

Frame Types: Wood, Plastic, and Foundationless

Frames hold the comb, and the choice of frame, whether wood or plastic, with wax foundation, plastic foundation or nothing at all, affects how much work you do, how your bees build, and how your equipment performs for years. This article compares the main frame types, explains the parts of a frame, covers assembly and reinforcement, and offers guidance on which to use for brood and for honey. I have assembled thousands of frames, and the advice here reflects the failure points I keep seeing in other people's equipment.

Anatomy of a Langstroth frame

A standard frame has four parts:

  • Top bar: the long upper piece, with ears that rest on the box rabbet.
  • Side bars: the two vertical sides.
  • Bottom bar: which may be solid, split, or absent in some designs.
  • Foundation or comb: the wax or plastic sheet the bees build on, or bare wax created by the bees themselves.

Frames hang from the top bar ears, and bee space is maintained around the sides and bottom. The frame is the working unit of a Langstroth hive; you lift it, inspect it, move it, and extract honey from it. For the full hive context see Langstroth Hive: The Standard Explained.

All-wood frames

Traditional frames are wood: pine, basswood or similar. Advantages:

  • Bees accept wood readily, and the material is natural.
  • It is easy to repair, reinforce and customise.
  • Wax adheres well to wood.
  • Cost is moderate, especially for kits.

Disadvantages:

  • Assembly takes time and some skill.
  • Wood can swell, warp or rot, especially if left wet.
  • Wax moths and beetles can use wood and old comb for hiding.
  • Wire and foundation placement takes practice.

Wooden frames last decades if you protect them from moisture and clean them occasionally. Reinforce joints with nails and glue, and wire the frame if you plan to extract with a motorised machine, since comb can blow out.

Plastic frames

Plastic frames are moulded in one piece, often with built-in foundation. Advantages:

  • No assembly, with quick set-up.
  • Durable, easy to clean, resistant to wax moths.
  • Strong enough for extraction without wiring.
  • Easy to scrape and reuse.

Disadvantages:

  • Some bees resist drawing plastic; wiping with wax or spraying with sugar water may help.
  • Over time, old comb and propolis build up, and scraping can be messy.
  • Some people dislike the plastic material for philosophical reasons.
  • Plastic frames can warp if overheated, and they are harder to repair.

Many beekeepers compromise: plastic in honey supers, wood in brood boxes. For the foundation decision, see Wax Foundation vs. Plastic Foundation.

Wooden frames with plastic foundation

This hybrid frame uses a wooden frame with a plastic foundation sheet inserted in a slot. It gives some of the benefits of both: wooden surfaces that bees accept, and a plastic sheet that resists blowout in extraction. Bees often draw it readily if you coat it with wax.

Foundationless frames

Foundationless frames have no sheet at all, only a guide, such as a wooden strip, a wax bead, or a groove. The bees build all their own comb. Benefits include natural cell sizes, lower cost, and wax production. Drawbacks include the risk of cross-comb if frames are not aligned, and fragile comb when new. See Foundationless Frames: Pros and Cons for details.

Choosing frames for brood and honey

Use these guidelines:

  1. Brood boxes: wood with wax or plastic foundation, or foundationless with careful management. Bees draw brood comb best on materials they accept readily.
  2. Honey supers for extracting: plastic or wood with wired foundation, since the comb must survive spinning.
  3. Comb honey: thin foundation or foundationless frames, depending on the format.
  4. Nuc boxes: keep frame types consistent with the main hive for easy swaps.

If you plan to extract, check the extractor basket compatibility; see Extractor Types: Tangential vs. Radial.

Assembly tips from the bench

  • Use a jig or square to keep frames true, because crooked frames cause burr comb.
  • Glue and nail each joint; staples alone are not enough.
  • Pre-drill for nails near the ends to avoid splitting.
  • Embed wire carefully; too much tension warps the frame.
  • Allow glue to dry before inserting foundation.
  • Label frames by year or colony if you rotate old comb out.
  • Store frames dry and sealed, protected from wax moths, using methods that follow product labels.

Spacing and maintenance

Frames should have consistent spacing so combs are even. Frame spacers or metal ends help, as do wide-top bars. Replace frames when comb is dark and damaged or when cell size shrinks due to repeated brood rearing; many beekeepers rotate out a portion of old comb every year or two. Old comb can hold residues from past treatments or disease, and cycling older frames out reduces risks. For how to read what your frames are telling you, see Reading Frames: Brood, Honey, Pollen, and Empty Comb.

Common mistakes

  • Mixing frame sizes in a single box.
  • Skipping wire for extraction frames.
  • Leaving frames wet and moulding.
  • Using too few frames per box, which leads to burr comb; fill the box fully or use follower boards.
  • Not scraping propolis, which makes frames hard to remove.
  • Ignoring old, dark comb.

Frame feeders, ears and hardware

Small details affect how frames behave over years of handling. Top bar ears should be long enough to rest securely on the rabbet but not so long that they catch on the hive tool or crush bees. Some frames have wide-spaced or self-spacing side bars, which keep distances even and reduce burr comb, though they can trap bees and cause crushing if you are careless. Metal frame rests prevent bees from gluing the ears to the box, and they make frames slide more easily, especially in hot weather when propolis is soft. Frame grips and a good hive tool make removal safer; see Hive Tools: J-Hook, Auto-Rotate, and Standard.

Always store spare frames flat or on edge in a dry place, and avoid stacking them where mice or moths can reach. Mark the date on the top bar in pencil, so you know when to retire a frame. A small investment in hardware and labelling saves hours in the apiary, and it makes comparisons among colonies more reliable.

FAQ

Should I wire my frames?

Wiring is optional for wood frames used only for honey in a hand-crank extractor, but it is strongly recommended for brood frames and any frames extracted in a motorised machine, since it keeps comb from collapsing.

Do bees prefer wood or plastic?

Bees will use both, but they often draw wax foundation on wood more quickly, and plastic may need a wax coating to encourage them.

How often should I replace old frames?

Many keepers cycle out a portion of comb every few years, replacing frames when comb is very dark, damaged, or has small, deformed cells.

Keep learning

Browse all 500 guides →